> For the complete documentation index, see [llms.txt](https://doc.engenius.ai/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://doc.engenius.ai/smartnic-bmc-user-guide/getting-started/introduction.md).

# Introduction

This guide describes the ESN904 Baseboard Management Controller (BMC) web interface built on the Insyde® Supervyse platform. It explains the available menus, features, and operational procedures in detail.

## Purpose of this Guide

You can use this guide to:

* Navigate the BMC web interface
* Review system and hardware information
* Manage logs and diagnostics
* Perform remote operations such as power control, firmware updates, KVM, and SOL
* Configure security, networking, and system parameters

The guide is intended for administrators or technical engineers managing ESN904 systems.

## About the BMC Web Interface

The ESN904 BMC web interface provides a graphical, browser-based platform for out-of-band system management.

Using the BMC interface, you can:

* Monitor real-time system and sensor data
* Access hardware inventory and status
* Review and download event logs.
* Perform remote power operations
* Launch the KVM or SOL console
* Configure BIOS remotely
* Manage user authentication and security settings
* Configure networking and virtual media settings

The BMC web interface is accessible over the dedicated management network port using any supported modern browser.

## Supported Browsers and Requirements

The BMC web interface supports the following browsers:

* Google Chrome (latest version recommended)
* Mozilla Firefox (latest version recommended)
* Microsoft Edge (latest version recommended)

Browser performance and behavior may differ based on version and security policies. For the best experience, always use the latest stable version.

## Default Login Credentials

**Check BMC IP address via the command line**

If the system has already booted into an operating system (Linux or Windows), you can retrieve the current BMC IP configuration using the ipmitool command.

* On Linux (as root): `ipmitool lan print 1`
* On Windows (run PowerShell as Administrator): `ipmitool.exe lan print 1`
* Typical output:&#x20;

| Set in Progress    | Set Complete   |
| ------------------ | -------------- |
| IP Address Source  | Static Address |
| IP Address         | 192.168.0.120  |
| Subnet Mask        | 255.255.255.0  |
| Default Gateway IP | 192.168.0.1    |

If multiple BMC channels are present, try the following commands to identify the active one: `ipmitool lan print 2`, `ipmitool lan print 3`.

**Set a static BMC IP address**

To configure a static IP address instead of using DHCP, run the following commands:

| `ipmitool lan set 1 ipsrc static`             |
| --------------------------------------------- |
| `ipmitool lan set 1 ipaddr 192.168.0.120`     |
| `ipmitool lan set 1 netmask 255.255.255.0`    |
| `ipmitool lan set 1 defgw ipaddr 192.168.0.1` |

After setting the values, verify the configuration: `ipmitool lan print 1`. This ensures that the BMC network configuration is correctly applied and remains persistent across reboots.

**Accessing the web interface**

The Insyde BMC web interface is accessible via the configured BMC IP address. For example: https\://\<BMC-IP-ADDRESS> *(e.g., <https://10.0.174.13>)*

**Default login credentials (factory setting)**

<table data-header-hidden><thead><tr><th width="185.111083984375"></th><th></th></tr></thead><tbody><tr><td>Field</td><td>Default Value</td></tr><tr><td>Username</td><td><mark style="color:blue;">root</mark></td></tr><tr><td>Password</td><td><mark style="color:blue;">0penBmc</mark></td></tr><tr><td>IP address</td><td>DHCP (recommended to use a static IP address)</td></tr></tbody></table>

{% hint style="info" %}
**Note:** The first character in <mark style="color:$success;">**0penBmc**</mark> is the digit **zero**, not the letter “O”.
{% endhint %}

{% hint style="warning" %}
I**mportant:** It is strongly recommended to change the default credentials immediately after the first login to prevent unauthorized access.
{% endhint %}


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://doc.engenius.ai/smartnic-bmc-user-guide/getting-started/introduction.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
